Vertical Rollerskating

Vert-Skating-Forum

Message 12829 (19. Jun. 2010 16:08) (Tree)

Bernhard
bernhard@adinfinitum.de
More Strickywear
You are right, it would seems that steering is affected. I noticed this too, but could not express it as well as you.
  Write reply

Replies

ireNe: More Strickywear (18. Jun. 2010 14:12)
 Nice work!


captcha: require unmake
  Write reply
Ufra: More Strickywear (18. Jun. 2010 16:48)
 I saw the other day.And I think...... COGRATULATIONS ISRA GAMBIN, VERY GOOD WORK.
Were you leaving me to prove them? I hope XDDDD
  Write reply
Robert: More Strickywear (18. Jun. 2010 18:08)
 Those look so great, but I am confused. Are they a plate or just a slider?
  Write reply
biffsk8er: More Strickywear (18. Jun. 2010 19:43)
 Sliders.

Those are inline boots (looks like Xsjados). They already have plates on them made of hard plastic. Looks to me like the skateboard trucks are bolted directly to that configuration with UHMW sliders added in the middle.

  Write reply
biffsk8er: More Strickywear (18. Jun. 2010 19:45)
 Also, here is his strickywear site. That link should also translate it to english for you.
  Write reply
Robert: More Strickywear (19. Jun. 2010 04:42)
 Those look so awesome, but I am curious about the line up of the trucks. It seems the euopeans and maybe others have the trucks higher up on the foot. I am used to the trucks being under the ball of my foot. Is it harder to skate with the trucks so far up? I like the fact that it gives you more room on the plate for tricks.
  Write reply
claudine: More Strickywear (19. Jun. 2010 05:56)
 Nice, Yours Irene? I think those sliders would go down too low even for me. I would never get off the coping, splat, hehehe.
  Write reply
biffsk8er: More Strickywear (19. Jun. 2010 07:29)
 : Those look so awesome, but I am curious about the line up of the trucks. It seems the euopeans and maybe others have the trucks higher up on the foot. I am used to the trucks being under the ball of my foot. Is it harder to skate with the trucks so far up? I like the fact that it gives you more room on the plate for tricks.

I skate with my trucks as far apart as possible. I\'ve found it is very helpful when skating vert.
  Write reply
biffsk8er: More Strickywear (19. Jun. 2010 07:33)
 : Nice, Yours Irene? I think those sliders would go down too low even for me. I would never get off the coping, splat, hehehe.

Funny.....I saw them and thought they did not go low enough!!! Ha!

Captcha fatally 3d
Sounds like what we do.
  Write reply
cephalopoid: More Strickywear (19. Jun. 2010 13:50)
 That looks like a really nice setup, with some really nice frames.
  Write reply
claudine: More Strickywear (19. Jun. 2010 14:27)
 I like my front trucks under the base of my toes, further forward its too hard to turn.
  Write reply
bnwsk88: More Strickywear (19. Jun. 2010 15:35)
 I agree with Biff, I for a long time skated with the more "proper" arrangement of having the front trucks under the ball of my foot, when I made my plate I considered it but opted for the extra clearance for sliding and the stability of the longer wheel base and pushed the trucks as far a part as possible. I love it and have not noticed any problem with carving or making lines happen. If I were rink skating I would set them differently but I think it really helps for vert skating. I do maintain some toe stop/slide area and find that works well for nose grinds.
  Write reply
bnwsk88: More Strickywear (19. Jun. 2010 16:01)
 here is a question. It would appear from the photo that the ends of the slider could interfere with the turning action of the trucks. Am I deceived? Could this be shortened to allow for greater turning action?
  Write reply
Bernhard: More Strickywear (19. Jun. 2010 16:08)
 You are right, it would seems that steering is affected. I noticed this too, but could not express it as well as you.
  Write reply
biffsk8er: More Strickywear (19. Jun. 2010 19:22)
 I wouldn't think that there would be a problem with the slider interfering with the trucks. If you enlarge the picture and look really close, you'll see that the slider slopes back underneath. That would allow the truck to pivot without hitting the slider.

When you push one side of the truck down towards the boot, you'll notice the other side of the truck moves up and away from the slider (forward in front / backwards in the rear), while the depressed side moves down and under the slider.

No prob.
  Write reply
Robert: More Strickywear (19. Jun. 2010 19:25)
 This is very interesting to hear about truck placement and wheel base. It seems like it would be a little harder to turn, but the extra space on the plate would be awesome. I did skate inlines for a year and I adapted to having the front wheel past the toe of my skate. I wish equipment was more accessible so I could try different things. My rollerskate set up has been working pretty well lately. I like my trucks really loose. Oh, and would would highly recommend Rainskates wheels. They are fast, but als grippy.
  Write reply
biffsk8er: More Strickywear (19. Jun. 2010 21:35)
 Those wheels look great!!


  Write reply
Bernhard: More Strickywear (19. Jun. 2010 21:46)
 Drool!
  Write reply
Gambin: More Strickywear (22. Jun. 2010 14:10)
 Sorry.. i'm Bussy and I haven't more time.

This Sliders is for a Street using... I does the sliders thinking in the hand-rails, the end not affected the turn action, you can see in the pics in picasa, I cut the end of the sliders think this.

Boot: is a Damian Wilson Pro-model from Xsjado
Trucks: Tracker Dart Fulltrack
Wheels: Powell Bomber 64mm 85A (Perfect for Street)
Bearings: Bones REDZ
Sliders: Strickywear Grooved Sliders

Keep Roll..!!!

PD: Bernhard.!! I'm finished Sven's Skates I want Shippin This Saturday!!


  Write reply
Bernhard: More Strickywear (22. Jun. 2010 14:38)
 : PD: Bernhard.!! I'm finished Sven's Skates I want Shippin This Saturday!!

Hip, hip, hurray! I'm looking forward to this very much!
  Write reply
Go to the Vert-Skating-forum